Hybrid nanofluid increases channel convective heat transfer by 34%
Researchers found that a hybrid nanofluid of carbon nanotubes and MXene nanoparticles in water improved convective heat transfer by 34% compared to standard water cooling.
Researchers in mechanical engineering have found that using a hybrid nanofluid composed of carbon nanotubes and MXene nanoparticles in deionized water can enhance convective heat transfer by up to 34% compared to traditional water cooling methods. This study, published in Discover Mechanical Engineering, evaluated the thermofluidic behavior of this hybrid suspension under controlled conditions, with wall heating at 50 degrees Celsius and an entering fluid temperature of 23 degrees Celsius. The hybrid nanofluid not only improved heat absorption but also reduced the time needed for thermal stabilization by about 22% in turbulent flow regimes. These results suggest potential applications in designing compact, efficient cooling systems for high-heat-flux electronic devices, energy conversion machinery, and microchannel heat exchangers.
The research aimed to determine if combining high-aspect-ratio carbon nanotubes with conductive MXene sheets in water could address heat-spreading limitations, reduce internal thermal resistance, and stabilize downstream temperature profiles under varying turbulent flows.
To ensure a consistent testing medium, the researchers prepared the carbon nanotube and MXene suspension using a two-step method. They accurately measured dry carbon nanotubes and MXene powders to achieve nanoparticle loadings of 0.15% and 0.20% by volume, then mixed them into deionized water. The mixture was stirred for uniform dispersion and subjected to high-frequency ultrasonic treatment to break down agglomerates. The suspension was visually monitored to prevent sedimentation before testing. Each batch was brought to an equilibrium inlet temperature of 23 degrees Celsius before being introduced into the experimental channel loop.
The experimental setup consisted of a closed-loop hydrodynamic and thermal test circuit designed for continuous flow and precise sensor data collection. Fluid was circulated by a motor-driven pump through delivery lines, a flowmeter, and inlet nozzles into a central stainless-steel channel. The channel was heated to 50 degrees Celsius using calibrated elements, and four thermocouples (T1, T2, T3, T4) recorded temperatures at various points.
The study explored four operational variables to map the channel's performance. Turbulent flow regimes were tested with Reynolds numbers from 10,000 to 25,000, promoting boundary-layer disruption. The channel's height-to-diameter ratio was varied across five settings (4, 6, 8, 10, 16) to assess the impact on fluid circulation and thermal resistance. The channel was tested at different inclinations (0, 90, 180, 360 degrees), and nanoparticle concentrations were alternated between 0.15% and 0.20%.
The hybrid nanofluids consistently outperformed water in heat absorption across all configurations. Water operated between 26.45 and 27.12 degrees Celsius, while the nanofluid maintained a tighter range of 26.79 to 27.29 degrees Celsius. The highest heat transfer enhancement of 34% occurred at a 0.20% nanoparticle loading and a channel ratio of 4. The system reached steady-state thermal stability 22% faster, indicating improved energy diffusion.
Increasing nanoparticle loading from 0.15% to 0.20% improved thermal dispersion and temperature uniformity. At 0.15%, the thermal spread was 0.84 degrees Celsius, while at 0.20%, it reduced to 0.61 degrees Celsius. This suggests that higher particle volumes enhance heat spreading and prevent localized heat retention without causing viscosity-induced flow issues.
Higher flow velocities and turbulence further improved the nanofluid's heat removal capabilities. At a Reynolds number of 10,000, water had a thermal spread of 0.76 degrees Celsius, while the nanofluid's range was 0.35 degrees Celsius. At 20,000, the nanofluid's range compressed to 0.32 degrees Celsius, and at 25,000, it maintained a uniform distribution between 26.79 and 27.06 degrees Celsius.
The channel's height-to-diameter ratio affected heat absorption and temperature uniformity. At a ratio of 4, the nanofluid's temperature variation was 0.48 degrees Celsius. As the ratio increased to 8, 10, and 16, the variation reduced, confirming that larger ratios favor uniform temperature distribution.
Channel orientation influenced convective circulation. Horizontal alignment at zero degrees set the baseline for heat dissipation. Vertical orientation at 90 degrees optimized performance by enhancing buoyancy-driven currents. Other orientations showed minor thermal reductions, with the nanofluid maintaining a spread of 0.41 degrees Celsius, indicating stable performance regardless of orientation.
Thermocouples T1 to T4 showed steady temperature increases along the flow path, confirming continuous heat diffusion. At T1, water ranged from 26.45 to 27.23 degrees Celsius, while the nanofluid ranged from 26.79 to 27.21 degrees Celsius. T4 recorded water between 26.49 and 27.29 degrees Celsius, and the nanofluid between 26.84 and 27.29 degrees Celsius.
Despite these findings, the researchers noted limitations, such as only testing two nanoparticle loadings and not measuring pressure drops, pumping power, or long-term stability. Future studies should explore broader concentrations, quantify pumping losses, and assess scalability for commercial applications.
Source: MXenes
